Understanding Frame Relay

Frame Relay

Frame relay is currently supposed the most perfect for new installations because it is the high performance WAN protocol. It was designed to use across ISDN interfaces but now a day it is used over an assortment of other network interfaces. Once a mastery of frame relay design and configure, it is much easier to obtain a strong understanding of x.25, ATM and SMDS. Frame relay operates at the physical and data link layers of the OSI model. Frame relay is an example of a packet switched technology. In a packet switched network, end stations dynamically share the network medium and available bandwidth and packets are switched between the various network segments until the destination is reached. Packet switched network technology accommodates more flexibility and more efficient use of bandwidth. Frame relay also known as the streamlined version of x.25 because of windowing and retransmission of the lost data.

Frame Relay Devices

There are two general types of the devices attached to a frame relay WAN, DTE and DCE.

• DTEs (Data Terminal Equipments) are generally terminating equipments for a specific network and typically located on the customer's premises that are personal computers, terminals, bridges and routers.

• DCEs (Data Circuit-terminating Equipments) are carrier owned internetworking devices and they provide clocking and switching services in a network.

Physical layer component and link layer component connect the DTE and DCE devices. A physical layer component defines the electrical, functional, mechanical and procedural specifications while a link layer component defines the protocols.

Frame Relay Network Subinterfaces

Frame relay network subinterfaces divide a single frame relay interface into multiple logical interfaces. A frame relay network subinterfaces addresses on point to point and multiple points.

• Point to point frame relay network subinterface can have only one DLCI associated with it and it does not use frame relay map statements. If multiple point to point frame relay network subinterfaces are configured for a single router and each frame relay network subinterface has an IP address assigned to it, each IP address must be assigned from a different network or subnetwork address space.

• Multiple points frame relay network subinterface can have multiple DLCIs assigned to it. They shares many of the characteristics of a physical frame relay interface and can be used the frame relay map statements.

The frame relay DLCI command is used to assign specific DLCIs to specific frame relay network subinterfaces. Without the frame relay network interface DLCI command all DLCIs are assigned to the physical interface. If a frame relay switch network subinterface addresses only 10 DLCIs to a router and only seven of the DLCIs are overtly assigned to existing subinterfaces on the switch, remaining DLCIs will be automatically assigned to the physical interface.

Frame Relay Switch

You can convert a Cisco router with multiple serial interfaces in to a frame relay switch with a minimal configuration. The commands for configuring a router as a frame relay switch are:

At global configuration mode type:

• frame-switch(config)#frame-relay switching

At the interface mode of interface serial 1, type:

• Frame-switch (config-if) #encapsulation frame-relay

• Frame-switch (config-if) #frame-relay intf-type dce

• Frame-switch (config-if) #frame-relay route 102 interface s2 201

  At the interface mode of interface serial2, type:

• Frame-switch (config-if) #encapsulation frame-relay

• Frame-switch (config-if) #frame-relay intf-type dce

• Frame-switch (config-if) #frame-relay route 201 interface s1 102

The values 102 and 201 are merely examples and you have to use whatever value you choose between the ranges of 16 to 1007.

Frame Relay PVCs and Class of Services

Frame relay network offer several design and configuration confronts. At the network layer address level, every connection with in a given frame relay network appears as if all are on the same network. For PVC based configurations, every remote network layer address will need to be mapped to a local DLCI in frame relay. Inverse ARP dynamically maps remote network layer address to local DLCIs on a frame relay DTE. Inverse ARP can only map addresses from remote frame relay devices that maintain directly connected PVC to the device performing the inverse ARP. Inverse ARP can provide a complete set of mapping in a full mash frame relay topology.

Configuring a Frame Relay Router Address Connect Broadcast

The minimum frame relay configuration on a Cisco router consists of a single command:

• Router (config)#interface serial 0

• Router (config-if)#encapsulation frame-relay

• Router (config-if)#no shutdown

With this single command, a Cisco router is ready to act as a frame relay DTE device. Once this command is typed, the interface is administratively enabled and frame relay announces the configured DLCIs to the router, inverse ARP execute to map remote network layer addresses to local DLCIs. The limitations of the inverse ARP can be remedied with three configuration alternatives and configure a frame relay router address connect broadcast.

• Add additional PVC between the satellite 1 and satellite 2.

• Configure frame relay map statement.

• Configure point to point subinterfaces.

Frame Relay vs ATM

You can find these similarities between the frame relay and ATM:

• They are virtual circuit based.

• They are NBMA technologies.

• They have burst rate features.

• They have congestions avoidance techniques.

• They have traffic shaping or management techniques.

• FECN of frame relay is equivalent to the EFCI of ATM.

• BECN of frame relay is equivalent to the RRM of the ATM.

  You can find these differences between frame relay and ATM:

• Frame relay is not cell based while ATM is cell based.

• Frame relay is not asynchronous while ATM is asynchronous.

• Frame relay has not a LANE deployment while ATM has the sort.

• Frame relay LMI is completely different then ATM ILMI.